I want to set the acquisition mode to Average + HR using SCPI commands. But I can not find the right command in the manual.

How can I add a attenuation table to my cable, used in my measurement setup?

and Impedance Analyzers from Rohde & Schwarz are ideal for measuring impedance at a fixed frequency as well as for determining the best operating point for the component under test The LCR Meters and Impedance Analyzers from Rohde & Schwarz are ideal for measuring impedance at a fixed frequency as well as for determining the best operating point for the component under test Impedance Measurements using

Application Note Peak and Mean Power measurements on wideband FMCW radar signals

Jun 28, 2019 | AN-No. 1EF107

This application note provides practical hints to accurately characterize and de-embed these lead-in and lead-out structures with R&S Vector Network Analyzers ZNA, ZNB, ZNBT and ZND.

Sep 19, 2022 | AN-No. 1SL367

Sep 16, 2020 | 新闻发布 | Aerospace

R&S ATC-SBC, the new session border controller from Rohde & Schwarz, has a secure voice connection for safe air traffic control operation, is the only solution on the market that supports ED-137 standards and was developed in accordance with the ED-153 software assurance guidance.

Diamond Light Source makes the invisible visible with a little help from Rohde & Schwarz - Case Study

This post explains how to set up and conduct NPS benchmarking campaigns so that it gives you statistically sound insight into mobile network quality.

Jun 13, 2024 | 新闻发布 | THz communication

Rohde & Schwarz is advancing its pioneering sub-THz research in the D-Band and has reached important milestones. In collaboration with the Berkeley Wireless Research Center (BWRC), the test and measurement expert has successfully characterized a TX/RX multi-antenna chip (CHARM) operating at up to 140 GHz, using their D-Band over-the-air (OTA) test chamber. Academia and industry leaders agree that the 110 GHz to 170 GHz frequency range, known as D-Band, is critical for beyond 5G and 6G mobile communications and future automotive radar applications.

A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?

In this webinar, we will demonstrate the fastest and most efficient ways to validate your RF components using real-world 5G and Wi-Fi scenarios, empowering you to streamline your testing processes.

R&S®Atomix LT - Fact Sheet

Animated avatar calls using augmented reality are one of the key application areas for 5G-Advanced. The R&S CMX500 radio communication tester empowers network operators to evaluate XR-based applications and services in a controlled environment, ensuring optimal performance and quality before mainstream deployment.

Oct 12, 2022 | 新闻发布 | Test & measurement

Cubtek Inc. is using network analyzers from Rohde & Schwarz in the development of 4D imaging radar for RF measurement of the E-band. Rohde & Schwarz oscilloscopes and their independently developed, application-specific integrated circuits (ASIC) provide the best measurement tools for automotive radar research and development.

Venice 4K, Clipster, SpycerBox Ultra TL, Headend AVHE100, Sky

The signal generator come in different frequency ranges. Using a program is there a way to tell the frequency range of the SMB100A for example?

I want to control my HMP using the RS-232 port on the HO720. Unfortunately i do not get any response from the device.

I perform a calibration with remote commands. With the command to start the calibration sweep with a short standard I get this error message. What is the problem?

Learn how the R&S®SFI100A vector signal generator can be used with the NRP Power Sensors to realize close loop power control at the output of a device under test such as a power amplifier. Learn how the R&S®SFI100A vector signal generator can be used with the NRP Power Sensors to realize close loop power control at the output of a device under test such as a power amplifier.

MIPI D-PHY is a low-power, cost-effective physical layer interface, essential in mobile devices and advanced technology systems. It's a high-speed, source-synchronous interface used in smartphone cameras, smartwatch displays, drones, in-car entertainment, automobile cameras, and radar sensors. This application note explores MIPI D-PHY's features, functionality, and testing practices for device compliance, addressing common issues. It highlights Rohde & Schwarz's equipment for ensuring compatibility and solving issues with MIPI D-PHY, aligned with MIPI D-PHY specification version 2.5.Developed by the MIPI Alliance, D-PHY connects cameras and displays to a host processor via CSI-2 or DSI protocols. It features a master-slave, asymmetrical design for reduced link complexity. Key aspects include a unidirectional clock, optional data signal directions, different data rates for half-duplex operation, point-to-point communication, and high-speed (HS) and low-power (LP) modes for data transfer and battery preservation. In HS mode, D-PHY uses differential signaling with specific impedance, while in LP mode, it operates in a single-ended manner with high impedance termination.The application note from Rohde & Schwarz provides insights into characterizing and debugging MIPI D-PHY, offering conformance verification with MIPI Alliance standards and protocol decoding options.

Jan 31, 2024 | AN-No. 1SL410

Download Rohde & Schwarz's definitive guide to understanding the technology behind spectrum analyzer measurements.

I get an unwanted 1 kHz tone in the demodulated AF spectrum after starting the generator in the Expert Mode using dialing. Where does this tome come from?

Emission testing: Efficient emission testing with modern EMI test receivers. A deeper dive into power inductors’ saturation with the aim of optimizing performance. We plan to demonstrate this practically using the multitude of functions provided by MXO Oscilloscope.

Rohde & Schwarz instrument security manual for the R&S®NGU power supply series be used in a secured environment.

In this webinar,we review the challenges that mode-agile RADAR and EW threat emitters pose to traditional static threat library implementations.

In this session you will learn about the challenges of WARM radar and EW threat emitters testing, with a special focus on assessing the architecture of cognitive AI an ML systems used as RF countermeasures.

Learn how R&S IRAPS™, FEDS, and MathWorks’ DLP enable real-time RF signal classification in complex EW environments using machine learning.

Feb 19, 2020 | 新闻发布 | Wireless communications

Rohde & Schwarz and Decawave demonstrate test functions for the new generation of Decawave UWB devices with the new generation of Rohde & Schwarz radio communication tester, the R&S CMP200. With this solution, both companies address manufacturers planning wireless devices using Ultra Wideband (UWB) technology to provide secure location-based services.

I am using the I/O Logging function to write all remote commands sent to the ZNL(E) to file. But I can not find any logging file in the path mentioned in the manual: C:\ProgramData\Rohde-Schwarz\ZNL-FPL\ScpiLogging

Power Measurements on WLAN Modules with the R&S CMU 200 and with CMUgo

Oct 18, 2005 | AN-No. 1CM55